Categories

Hot Products

Knowledge

  • The cardan shaft is connected with the flanges at both ends by other high-strength bolts and self-locking nuts, and the transfer torque is transmitted through the frictional force between the flange end face key and the flange.……
    Feb 12
    2019
  • The universal joint is a type of coupling for the mechanical transmission member, and it can be said that the universal joint belongs to the coupling family.……
    Feb 10
    2019
  • Cross and bearings shall avoid collision and stacking when disassembling, handling and stocking, so the engine should be at full stop.……
    Feb 09
    2019
  • If you want to really achieve the high-performance in the agricultural machinery, it is necessary to carry out on-the-spot measurement and tailor-made agricultural drive shafts.……
    Feb 08
    2019
  • The diaphragm coupling is known for its compactness, but because of its ingenuity, it is necessary to pay attention to during installation and use.……
    Feb 07
    2019
  • It is very necessary to remove the oil before the finishing of the gear spindles parts and to dehydrate and dry the rust after the finishing, and both are indispensable.……
    Feb 06
    2019
  • The quality of the raw materials of the forging rings is a prerequisite for the quality of the forgings.……
    Feb 05
    2019
  • ​The forging process used in the forging flange production process generally consists of the following processes, namely, billet blanking, heating, forming, and post-forging cooling.……
    Feb 04
    2019
  • If you want to buy a really good universal joints, you should first choose a trust worthy brand. The better the brand, the better the functionality, quality, and after-sales of the product.……
    Feb 03
    2019
  • For the universal joint shaft with telescopic features, it is necessary to check that the spline sleeve and the spline shaft be matched properly when installing, so as to ensure that the phase difference between the axes of the bearing ends of the fo……
    Feb 02
    2019
  • Universal joints are subjected to a large torque and alternating load during work. However, due to the poor toughness of the oil film of the calcium-based grease, it is difficult to form a good oil film on the friction surface of the bearing and the ……
    Feb 01
    2019
  • It is clearly stated in the general vehicle maintenance manual that the key teeth and the intermediate bearing of the transmission shaft telescopic sleeve use calcium-based grease, and the cross and bearings and the three-bridge drive the intermediat……
    Jan 31
    2019
  • The agricultural drive shaft is applied to the power transmission of modern agricultural machinery, the transmission of power between the most common tractor and agricultural implements or the power output and input of the agricultural machinery itse……
    Jan 30
    2019
  • Drive shafts are mainly used to connect the universal joints of various mechanisms.……
    Jan 29
    2019
  • The torque detection of the gear spindles is detected by the torque measuring device. It can be judged by the torque detection whether the torque reaches the maximum torque required by the design, which is very important for ensuring the safe use of ……
    Jan 28
    2019
  • The iron crystal structure changes during the forging process. The first is the initial stage of deformation, forming a substructure with high density dislocations. These dislocations can be homogeneously distributed or become sub grain boundaries of……
    Jan 27
    2019
  • With the continuous development of the economy, the actual demand for forging flanges in the industry is increasing, and its performance is very prominent which increases their popularity.……
    Jan 26
    2019
  • For front-wheel drive vehicles, the drive shaft is a constant universal joints, and some universal joints are sealed with a rubber sleeve.……
    Jan 25
    2019
  • It is clearly stated in the general vehicle maintenance manual that the key teeth and the intermediate bearing of the transmission shaft telescopic sleeve use calcium-based grease, and the cross and bearings and the three-bridge drive the intermediat……
    Jan 24
    2019
  • The agricultural machinery drive shaft is applied to the power transmission of modern agricultural machinery, the transmission of power between the most common tractor and agricultural implements or the power output and input of the agricultural mach……
    Jan 23
    2019
First Prev 1234 Next Last 1/4
  • QR CODE
  • facebook